This diagram shows all the parts of the Orb and the corresponding number of each part. To avoid any misunderstanding, please refer to these names and numbers when discussing the Orb assembly with your consultant.
Orb Components
Bottom Orb Shell (Base)
Bottom Button (Bottom Ring Assembly)
Positive Ring (Sharp Edge facing UP)
Positive Track
Centre Module (Copper & two Rings)
Positive Ring (Sharp Edge facing DOWN)
Top Button (Top Ring Assembly)
Top Orb Shell
Cable Connector (Mohawk)
Locking clip
Step 1a. Begin with the Bottom Shell (Orb Base)
Step Explanations:
Begin the Assembly by taking the Bottom Orb Shell (#1).
Take note of the brass post recess as shown here.
Step 1b. Insert the first Ring with Brass Post.
Step Explanations:
Press the Bottom Button (#2) into the Bottom Orb Shell with the Brass Post pointing down to fit into the recess.
Step 2. Inserting the 2nd Ring.
Step Explanations:
Place one Positive Ring (#3) into the Orb Shell.
For optimal performance please ensure that the less-rounded edge of the Positive Ring face up.
Step 3. Inserting the Positive Track.
Step Explanations:
Place the Positive Track (#4) into the Orb Shell, resting on (A) the Positive Ring and (B) the indent on the Orb Shell.
Step 4. Inserting the Centre Module.
Step Explanations:
Fit the Centre Module (#5) into the Orb Shell between the Positive Track arms as shown, (B) ensuring that the Negative Track (A) is directly opposite the Positive Track. The Centre Module (#5) should rest on the Bottom Button (#2) and be level within the Orb Shell.
Step 5. Inserting the 2nd Positive Ring.
Step Explanations:
Place the remaining Positive Ring (#6) into the Orb resting on top of the Positive Track (#4) as shown (A).
For optimal performance please ensure that the less-rounded edge of the Positive Ring faces down.
Step 6a.
Step Explanations:
Take the Top Orb Shell (#8) and locate the hole in the top.
Step 6b. Inserting the Top Button.
Step Explanations:
Insert the Top Button (#7) into the Top Orb Shell so that the Brass Post protrudes through the hole. Gently rotate it so that it goes in smoothly. It should hold in firmly.
Step 7a. Fitting the Top Orb Shell.
Step Explanations:
Align the arrows (A) on the rear of the Orb Shell. When placed correctly, the Tab on the rear of the Bottom Orb Shell (B) will match up with the Hole (B) on the rear of the Top Orb Shell.
Step 7b. Closing the Top Orb Shell.
Step Explanations:
Close the Top and Bottom Orb shells as if hinged at the back. The small indent in the Top Shell (C) will align with the Positive Track Eyelet (#4).
Step 8a. Locate Guide Slots.
Step Explanations:
Locate the Guide Slots and the Top Slot in the Orb.
Step 8b. Fitting the Cable Connector.
Step Explanations:
Slide the tip of the Cable Connector (#9) into the Top Slot of the Orb. Align the Guide Pins with the Guide Slots in the Orb and push the Cable Connector firmly against the Orb.
Step 9. Locking the Cable Connector inplace.
Step Explanations:
Ensure that there is no gap between the Orb and the Cable Connector. Whilst holding the Cable Connector firmly against the Orb, slide the Locking Clip (#10) upward fastening the Cable Connector to the Orb.
Step 10. Locking the Cable Connector in place.
Step Explanations:
Ensure the Locking Clip clicks over the top of the Locking Pins on the Cable Connector.
Your Orb is now complete.
Step Explanations:
Your Orb is now complete and ready to begin a QEnergySpa session.
